2903144
TRIO-PS-2G/1AC/24DC/5/B+D
Width: | 35 mm |
Height: | 130 mm |
Depth: | 115 mm |
Installation distance right/left: | 0 mm / 0 mm |
Installation distance top/bottom: | 50 mm / 50 mm |
Degree of protection: | IP20 |
Inflammability class in acc. with UL 94 (housing / terminal blocks): | V0 |
Ambient temperature (operation): | -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K) |
Ambient temperature (start-up type tested): | -25 °C |
Ambient temperature (storage/transport): | -40 °C ... 85 °C |
Max. permissible relative humidity (operation): | ≤ 95 % (at 25 °C, non-condensing) |
Climatic class: | 3K3 (in acc. with EN 60721) |
Degree of pollution: | 2 |
Installation height: | ≤ 5000 m (> 2000 m, observe derating) |
Nominal input voltage range: | 100 V AC ... 240 V AC |
Input voltage range: | 100 V AC ... 240 V AC -15 % ... +10 % |
Dielectric strength maximum: | ≤ 300 V AC 15 s |
AC frequency range: | 50 Hz ... 60 Hz ±5 Hz |
Frequency range (fN): | 50 Hz ... 60 Hz ±10 % |
Discharge current to PE: | < 0.25 mA |
Current consumption: | 2.2 A (100 V AC) |
Nominal power consumption: | 272 VA |
Inrush current: | ≤ 16 A (typical) |
Mains buffering time: | typ. 20 ms (120 V AC) |
Input fuse: | 6.3 A (internal (device protection)) |
Recommended breaker for input protection: | 6 A ... 16 A (Characteristics B, C, D, K) |
Power factor (cos phi): | 0.5 |
Type of protection: | Transient surge protection |
Protective circuit/component: | Varistor |
Nominal output voltage: | 24 V DC ±1 % |
Setting range of the output voltage (USet): | 24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted) |
Nominal output current (IN): | 5 A |
Dynamic Boost (IDyn.Boost): | 7.5 A (5 s) |
Derating: | > 60 °C ... 70 °C (2.5%/K) |
Connection in parallel: | Yes, for redundancy and increased capacity |
Connection in series: | yes |
Feedback voltage resistance: | ≤ 35 V DC |
Protection against overvoltage at the output (OVP): | ≤ 30 V DC |
Control deviation: | < 1 % (change in load, static 10 % ... 90 %) |
Residual ripple: | < 50 mVPP (with nominal values) |
Output power: | 120 W |
Typical response time: | < 1 s |
Maximum power dissipation in no-load condition: | < 1 W |
Power loss nominal load max.: | < 16 W |
Net weight: | 0.45 kg |
Efficiency: | > 89 % (for 230 V AC and nominal values) |
MTBF (IEC 61709, SN 29500): | > 3380000 h (25 °C) |
Insulation voltage input/output: | 3 kV AC (type test) |
Degree of protection: | IP20 |
Protection class: | II (in closed control cabinet) |
Inflammability class in acc. with UL 94 (housing / terminal blocks): | V0 |
Mounting position: | horizontal DIN rail NS 35, EN 60715 |
Assembly instructions: | alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm |
Connection method: | Push-in connection |
Conductor cross section solid min.: | 0.2 mm² |
Conductor cross section solid max.: | 4 mm² |
Conductor cross section flexible min.: | 0.2 mm² |
Conductor cross section flexible max.: | 2.5 mm² |
Conductor cross section AWG min.: | 24 |
Conductor cross section AWG max.: | 12 |
Stripping length: | 10 mm |
Connection method: | Push-in connection |
Conductor cross section solid min.: | 0.2 mm² |
Conductor cross section solid max.: | 4 mm² |
Conductor cross section flexible min.: | 0.2 mm² |
Conductor cross section flexible max.: | 2.5 mm² |
Conductor cross section AWG min.: | 24 |
Conductor cross section AWG max.: | 12 |
Stripping length: | 8 mm |
Connection method: | Push-in connection |
Conductor cross section solid min.: | 0.2 mm² |
Conductor cross section solid max.: | 1.5 mm² |
Conductor cross section flexible min.: | 0.2 mm² |
Conductor cross section flexible max.: | 1.5 mm² |
Conductor cross section AWG min.: | 24 |
Conductor cross section AWG max.: | 16 |
Stripping length: | 8 mm |
EMC requirements for noise immunity: | EN 61000-6-1 |
EMC requirements for noise emission: | EN 61000-6-3 |
Standard - Safety of transformers: | EN 61558-2-16 (air clearances and creepage distances only) |
Standard - Electrical safety: | IEC 60950-1/VDE 0805 (SELV) |
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations: | EN 50178/VDE 0160 (PELV) |
Standard – Safety extra-low voltage: | IEC 60950-1 (SELV) and EN 60204-1 (PELV) |
Standard - Safe isolation: | DIN VDE 0100-410 |
Standard – Limitation of mains harmonic currents: | EN 61000-3-2 |
Mains variation/undervoltage: | Semi F47-0706 |
Rail applications: | EN 50121-4 |
UL approvals: | UL Listed UL 508 |
Shipbuilding approval: | DNV GL (EMC B) |
Electromagnetic compatibility: | Conformance with EMC Directive 2014/30/EU |
Low Voltage Directive: | Conformance with Low Voltage Directive 2014/35/EC |
Electrostatic discharge: | EN 61000-4-2 |
Contact discharge: | 6 kV (Test Level 4) |
Discharge in air: | 8 kV (Test Level 4) |
Electromagnetic HF field: | EN 61000-4-3 |
Frequency range: | 80 MHz ... 1 GHz |
Test field strength: | 10 V/m (Test Level 3) |
Frequency range: | 1 GHz ... 2 GHz |
Test field strength: | 10 V/m (Test Level 3) |
Frequency range: | 2 GHz ... 3 GHz |
Test field strength: | 10 V/m (Test Level 3) |
Comments: | Criterion A |
Fast transients (burst): | EN 61000-4-4 |
Input: | 4 kV (Test Level 4 - asymmetrical) |
Output: | 2 kV (Test Level 3 - asymmetrical) |
Signal: | 1 kV (Test Level 2 - asymmetrical) |
Comments: | Criterion A |
Surge voltage load (surge): | EN 61000-4-5 |
Input: | 2 kV (Test Level 3 - symmetrical) |
Output: | 1 kV (Test Level 2 - symmetrical) |
Signal: | 1 kV (Test Level 2 - asymmetrical) |
Comments: | Criterion B |
Conducted interference: | EN 61000-4-6 |
Frequency range: | 0.15 MHz ... 80 MHz |
Voltage: | 10 V (Test Level 3) |
Comments: | Criterion A |
Criterion A: | Normal operating behavior within the specified limits. |
Criterion B: | Temporary impairment to operational behavior that is corrected by the device itself. |
REACh SVHC: | Lead 7439-92-1 |
eCl@ss 10.0.1: | 27040701 |
eCl@ss 4.0: | 27040700 |
eCl@ss 4.1: | 27040700 |
eCl@ss 5.0: | 27049000 |
eCl@ss 5.1: | 27049000 |
eCl@ss 6.0: | 27049000 |
eCl@ss 7.0: | 27049002 |
eCl@ss 8.0: | 27049002 |
eCl@ss 9.0: | 27040701 |
ETIM 3.0: | EC001039 |
ETIM 4.0: | EC000599 |
ETIM 5.0: | EC002540 |
ETIM 6.0: | EC002540 |
ETIM 7.0: | EC002540 |
UNSPSC 6.01: | 30211502 |
UNSPSC 7.0901: | 39121004 |
UNSPSC 11: | 39121004 |
UNSPSC 12.01: | 39121004 |
UNSPSC 13.2: | 39121004 |
UNSPSC 18.0: | 39121004 |
UNSPSC 19.0: | 39121004 |
UNSPSC 20.0: | 39121004 |
UNSPSC 21.0: | 39121004 |
ECCN: | |
Country of Origin: | CN |
EAN: | |
Weight: | 0.573 kg |
Length: | 0.00 m |
Width: | 0.00 m |
Height: | 0.00 m |